Ametek 1995A Micro-Set PLS Bedienungsanleitung Seite 1

Micro-Set Programmable Limit SwitchGemco®Series 1995AInstallation & Programming Manual

Chapter 3: ProgrammingInstallation and Maintenance Manual63.4: Number of OutputsThe 1995A comes programmed for six outputs, but it is expandable to

7Installation and Maintenance ManualChapter 3: Programming3.7: Setpoint FormulaWhere: A = 5 for 6 outputs= 6 for 12 outputs= 7 for 18 outputs= 8

Chapter 3: ProgrammingInstallation and Maintenance Manual8C) will display the total number of

9Installation and Maintenance ManualChapter 3: Programmingon a scale factor corresponding to the 360-degree rotation of the resolver. Example: In

Chapter 3: ProgrammingInstallation and Maintenance Manual103.9: Clear an Existing SetpointA) Unit must be in the Program mode.B) Depress .C) Depr

11Installation and Maintenance ManualChapter 3: ProgrammingOn units without Multiprogram, setpoint availability is dependent on the number of outpu

Chapter 3: ProgrammingInstallation and Maintenance Manual12Programming Reset-to-Preset ValueThe Reset-to-Preset Value is programmed by entering t

13Installation and Maintenance ManualChapter 3: Programming3.15: Power-Up in a Position or RPMThe 1995A can power up displaying either Position or

Chapter 3: ProgrammingInstallation and Maintenance Manual143.17: Enable/Disable OutputsDuring setup, the outputs may be enabled or disabled. When

15Installation and Maintenance ManualChapter 3: ProgrammingThe graph above shows an example of four steps of linear offset in which the output circ

iInstallation & Maintenance Manual1080 North Crooks RoadClawson, MI 48017-1097Phone: (248) 435-0700FAX: (248) 435-8120Internet: www.ametekap

Chapter 3: ProgrammingInstallation and Maintenance Manual163.19: Programming 1995 PLS for Linear SpeedA) Unit must be in the Program mode.B) Sele

Chapter 4: Expansion ModulesInstallation and Maintenance Manual18Chapter 4: Expansion ModulesThe 1995A PLS provides six outputs. A 1995E Expansion

17Installation and Maintenance ManualChapter 3: Programming3.21: Time-Based Outputs (Available Only on Option P Units)These outputs are programme

19Installation and Maintenance ManualChapter 5: Fault CheckChapter 5: Fault CheckThe Fault Check option provides an automatic in-process self-diagn

Chapter 5: Fault CheckInstallation and Maintenance Manual205.1: PLS Output Status on Fault Conditions1) If a fault condition is detected, ALL limit

21Installation and Maintenance ManualChapter 6: Security InputsChapter 6: Security InputsThe Run/Program security inputs may be operated by an isol

Chapter 7: Remote Circular DisplayInstallation and Maintenance Manual22Chapter 7: Remote Circular DisplayNOTE: When using a remote circular display

23Installation and Maintenance ManualChapter 8: TroubleshootingChapter 8: TroubleshootingNOTE: Field repair beyond this level is not recommended.8.

Chapter 8: TroubleshootingInstallation and Maintenance Manual24The 1995 PLS is designed for use in an industrial environment and incorporates exten

25Installation and Maintenance ManualChapter 8: TroubleshootingIf the resolver cable must be run through a terminal strip, it must be mounted in a

Installation & Maintenance ManualiiContentsChapter 1: Introduction/Description 11.1 Programmable Features ...

Chapter 9: SpecificationsInstallation and Maintenance Manual26Chapter 9: Specifications9.1: 1995 Micro-Set PLS Programmer9.2: Mechanical Relay (Sin

27Installation and Maintenance ManualChapter 9: Specifications9.4: DC Solid-State (Single Pole, Normally Open)9.5: 1995E Output Expansion Module9.6

Chapter 10: Troubleshooting GuideInstallation and Maintenance Manual28Chapter 10: Troubleshooting GuideMOTPMYS SESUACELBISSOPEEE:swohSyalpsiD ehtni

29Installation and Maintenance ManualChapter 10: Troubleshooting GuideMOTPMYS SESUACELBISSOPastibihxetubylreporpsetarepometsyS.stuptuollafossolyrat

Chapter 10: Troubleshooting GuideInstallation and Maintenance Manual30MOTPMYS SESUACELBISSOP.eriftonlliwsyalereludomnoisnapxE tcerrocrofseludomnois

31Installation and Maintenance ManualChapter 11: Wiring DiagramsFig 11-1 Wiring DiagramDrawing E0177100Chapter 11: Wiring Diagrams

Chapter 11: Wiring DiagramsInstallation and Maintenance Manual32Fig 11-2 Wiring DiagramDrawing E0204400

33Installation and Maintenance ManualChapter 11: Wiring DiagramsFig 11-3 Wiring DiagramDrawing E0198200

875A 01/03.Z655C1080 N. Crooks Road l Clawson, MI 48017800-635-0289 l 248-435-0700 l Fax 248-435-8120www.ametekapt.com l www.ametek.com

iiiInstallation & Maintenance ManualChapter 6: Security Inputs 21Chapter 7: Remote Circular Display 227.1 POS/RPM On Remote Circular Display

1Installation and Maintenance ManualChapter 1: Introduction/DescriptionScale Factor Two scale factors to choose from either 360 or 1,000. On units

Chapter 1: Introduction/DescriptionInstallation and Maintenance Manual2The completely self-contained unit can operate up to 30 independent outputs

3Installation and Maintenance ManualChapter 2: InstallationChapter 2: InstallationThis section describes the installation and wiring of a standard

Chapter 2: InstallationInstallation and Maintenance Manual42.2: Electrical InstallationThe Micro-Set is designed for use in an industrial environme

5Installation and Maintenance ManualChapter 3: ProgrammingChapter 3: Programming3.1: Security InputThe security input is often referred to as the 