Ametek PLA-PLW Programming Manual Bedienungsanleitung Seite 34
- Seite / 74
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
32
Returned Parameters <NRf+> POW? and POW:TRIG? return the presently programmed
power levels. After a trigger or ABORt, POWer:TRIG? returns the same
value as POWer? .
POWer? MAX, POWer? MIN, POWer:TRIG? MAX and POWer:TRIG?
MIN return the maximum and minimum programmable LEVel and
TLEVel values.
[SOURce:]POWer:[TRANsient:]DUTY
This command sets the duty cycle of each of the transients when the generator is in CONTinuous
mode.
Command Syntax POWer:[TRANsient:]DUTY <NR1>
Parameters Duty cycle value. 1 – 100
Unit Percentage (%)
Query Syntax POWer: DUTY?
POWer: DUTY? MIN POWer: DUTY? MAX
POWer:TRANsient:DUTY?
POWer:TRANsient:DUTY? MIN POWer:TRANsient:DUTY? MAX
Returned Parameters <NR1> Duty cycle value in percentage.
[SOURce:]POWer:[TRANsient:]FREQuency
This command sets the frequency of the transients when the generator is in CONTinuous mode.
Command Syntax POWer:[TRANsient:]FREQuency <NRf+>
Parameters Frequency value, refer to model specifications for range | MIN | MAX
Unit Hertz
*RST Value 1.0 Hz
Query Syntax POWer:FREQuency?
POWer:FREQuency? MIN POWer:FREQuency? MAX
POWer:TRANsient:FREQuency?
POWer:TRANsient:FREQuency? MIN
POWer:TRANsient:FREQuency? MAX
Returned Parameters <NRf+>, frequency value.
[SOURce:]POWer:PROTection[:LEVel]
[SOURce:]POWer:PROTection:OVER[:LEVel]
[SOURce:]POWer:PROTection:DELay
[SOURce:]POWer:PROTection:OVER:DELay
[SOURce:]POWer:PROTection:UNDer:DELay
[SOURce:]POWer:PROTection:STATe
[SOURce:]POWer:PROTection:UNDer[:LEVel]
[SOURce:]POWer:PROTection:UNDer:STATe
Channel-Specific Power Limiting Command/Query. This command sets the over-power
protection limit or the under-power protection limit to the input power that the electronic load will sink.
When the input power reaches the over-power protection limit or falls below the under-power
protection limit for the specified delay period, the input of the electronic load is shut off and draws no
power.
The INPut:PROTection:CLEar command (or front panel key) re-enables the input power. The trigger
activated power functions (POWer[:LEV]:TRIG and POWer:TLEV) automatically keep track of
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Verwandte Produkte und Handbücher für Ausrüstung Ametek PLA-PLW Programming Manual
Ausrüstung Ametek PLA-PLW Bedienungsanleitung
(128 Seiten)
(128 Seiten)
Ausrüstung Ametek FPDC Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Ametek ACPS Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Ametek HPAL Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Ausrüstung Ametek SFA Series Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Ausrüstung Ametek ReFlex Bedienungsanleitung
(359 Seiten)
(359 Seiten)
Ausrüstung Ametek SGA Series Bedienungsanleitung
(97 Seiten)
(97 Seiten)
Ausrüstung Ametek SLD Series Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Ausrüstung Ametek SGI Series Bedienungsanleitung
(128 Seiten)
(128 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern