Ametek PLA-PLW Programming Manual Bedienungsanleitung Seite 35
- Seite / 74
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
33
incoming triggers while the input is shut down and will respond to the trigger as soon as the protection
fault is cleared.
The :PROTection:DELay command specifies the time that the input power may equal or exceed
POWer:PROTection[:LEVel] or equal or fall below the POWer:PROTection:UNDer[:LEVel] before the
soft circuit breaker is actuated. The PROTection:STATe co mmand enables or disables the soft circuit
breaker function.
Note : If the soft circuit breaker function causes the input to shut down, it will not affect INP[STAT
e]. If
INP:
STAT is programmed ON, it will remain so even after the POWer:PROT has turned the electronic
load off.
Command Syntax
POWer:PROTection <NRf+> Set immediate overpower
protection limit.
POWer:PROTection:OVER <NRf+> Set immediate overpower
protection limit.
POWer:PROTection:DELay <NRf+> Set time that power may be at or
above :LEVel before input is turned off.
POWer:PROTection:OVER:DELay <NRf+> Set time that power may be at or
above :LEVel before inp
ut is turned
off.
POWer:PROTection:UND:DELay <NRf+> Set tim e that power may be at or
above :LEVel before input is turned off.
POWer:PROTection:STATe OFF|0 Disable over protection function.
POWer:PROTection:STATe ON|1 Enable over protection function.
POWer:PROTection:UNDer <NRf+> Set immediate under-power protection limit.
POWer:PROTection:UND:STAT OF|0 Disable under protection function.
POWer:PROTection:UND:STAT ON|1 Enable under protection function.
Parameters Refer individual model specification for |
MIN | MAX
Query
Syntax POWer:PROTection?
POWer:PROTection? MIN POWer:PROTection? MAX
POWer:PROTection:OVER?
POWer:PROTection:OVER? MIN
POWer:PROTection:OVER? MAX
POWer:PROTection:DELay?
POWer:PROTection:DELay? MIN
POWer:PROTectionDELay? MAX
POWer:PROTection:DELay?
POWer:PROTection:OVER:DELay? MIN
POWer:PROTection:OVER:DELay?MAX
POWer:PROTection:UNDer:DELay?
POWer:PROTection:UNDer:DELay? MIN
POWer:PROTection:UNDer:DELay? MAX
POWer:PROTection:STATe?
POWer:PROTection:UNDer?
POWer:PROTection:UNDer? MIN
POWer:PROTection:UNDer? MAX
POWer:PROTection:UNDer:STATe?
[SOURce:]POWer:SLEW:BOTH
This command sets the slew time for all programmed changes in the input power level of the
electronic load. This command programs both positive and negative going slew time. Although any
slew time value may be entered, the electronic load selects a slew time that is closest to the
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Verwandte Produkte und Handbücher für Ausrüstung Ametek PLA-PLW Programming Manual
Ausrüstung Ametek PLA-PLW Bedienungsanleitung
(128 Seiten)
(128 Seiten)
Ausrüstung Ametek FPDC Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Ametek ACPS Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Ametek HPAL Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Ausrüstung Ametek SFA Series Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Ausrüstung Ametek ReFlex Bedienungsanleitung
(359 Seiten)
(359 Seiten)
Ausrüstung Ametek SGA Series Bedienungsanleitung
(97 Seiten)
(97 Seiten)
Ausrüstung Ametek SLD Series Bedienungsanleitung
(89 Seiten)
(89 Seiten)
Ausrüstung Ametek SGI Series Bedienungsanleitung
(128 Seiten)
(128 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern